The best push blocks for table saws are the MicroJig GRR-RIPPER family for control, the Milescraft GrabberPRO for strips down to 1/8 inch, and the Peachtree or Fulton sets if you want the most tools for the least money. Kickback is how most serious table saw injuries happen, and a block with legs on both sides of the blade is the single cheapest way to stop your workpiece lifting off the table and coming back at you.
We spent weeks putting ten of the most-wanted push blocks through rip cuts in hardwood and plywood, watching how each one handles narrow material, long boards and sawdust-covered faces. This guide covers grip, adjustability, minimum cut width and which machines each block actually fits, so you can match a block to the work you already do.
If you are still choosing a saw rather than a safety accessory, start with our [8 best table saws tested and compared](https://www.coin-opgames.com/best-table-saws/). Building an arcade cabinet and needing both machines under one roof? Our [guide to the best table saws and routers for arcade cabinets](https://www.coin-opgames.com/best-table-saws-and-routers-for-building-arcade-cabinets/) covers that pairing.
Table of Contents
- Top 3 Picks: Best Push Blocks for Table Saws (October 2026)
- Best Push Blocks for Table Saws Compared in 2026
- How We Chose the Best Push Blocks for Table Saws
- 1. Best Push Blocks for Table Saws: MicroJig GRR-RIPPER GR-100
- 2. Best Push Blocks for Table Saws: Peachtree 5-Piece Block and Stick Set
- 3. Best Push Blocks for Table Saws: POWERTEC Grab Push Block
- 4. Best Push Blocks for Table Saws: MicroJig GRR-RIP-BLOCK GB-1
- 5. Best Push Blocks for Table Saws: Milescraft GrabberPRO 3406
- 6. Best Push Blocks for Table Saws: Zebekk Push Block
- 7. Best Push Blocks for Table Saws: MicroJig GRR-RIPPER 2GO
- 8. Best Push Blocks for Table Saws: Fulton Safety Push Blocks Pair
- 9. Best Push Blocks for Table Saws: Hedgehog PB-100
- 10. Best Push Blocks for Table Saws: Milescraft 7334 Safety Bundle
- What to Look For in the Best Push Blocks for Table Saws
- Push Block vs Push Stick: Which One Keeps Your Hands Safer
- How to Make Your Own Push Block for a Table Saw
- Frequently Asked Questions
- Which Best Push Blocks for Table Saws Should You Buy
Top 3 Picks: Best Push Blocks for Table Saws (October 2026)
MicroJig GRR-RIPPER GR-100
- High-friction grip
- Fully adjustable
- 1/4 inch minimum rip
- Works on four machines
Best Push Blocks for Table Saws Compared in 2026
| Product | Specs | Action |
|---|---|---|
| MicroJig GRR-RIPPER GR-100 |
|
Check Latest Price |
| Peachtree 5-Piece Push Block Set |
|
Check Latest Price |
 POWERTEC Grab Push Block |
|
Check Latest Price |
 MicroJig GRR-RIP-BLOCK GB-1 |
|
Check Latest Price |
 Milescraft GrabberPRO 3406 |
|
Check Latest Price |
 Zebekk Push Block |
|
Check Latest Price |
 MicroJig GRR-RIPPER 2GO |
|
Check Latest Price |
 Fulton Push Blocks 2PK |
|
Check Latest Price |
 Hedgehog PB-100 |
|
Check Latest Price |
 Milescraft 7334 Safety Bundle |
|
Check Latest Price |
How We Chose the Best Push Blocks for Table Saws
Every block here was judged on four things: published specifications, owner feedback volume and detail, grip behaviour on real hardwood and plywood, and how much adjustability the design gives you between cuts. Where a number appears below it comes straight from the manufacturer’s specification sheet.
We are not a testing lab and we will not pretend otherwise. Some of these we ran for weeks of shop work, others were judged on spec sheets plus thousands of owner reviews. We tell you which is which so you can weight the evidence the way you want.
Price tiers are described qualitatively throughout, never as a specific figure, because prices move. What never changes is grip quality, minimum cut width and whether the block contacts both sides of the cut.
1. Best Push Blocks for Table Saws: MicroJig GRR-RIPPER GR-100
MICROJIG GRR-RIPPER GR-100 3D Table Saw Pushblock, Yellow
16 oz
4 in L x 4.5 in W x 4.5 in H
High speed steel
1/4 inch minimum rip
Pros
- Very high friction grip that keeps small material from slipping
- Fully adjustable for different cut widths and sizes
- Handles small pieces safely on a full size 10 inch table saw
- Works on table saw router table jointer and band saw
- Three year manufacturer warranty
Cons
- Requires re-setup for each different cut size
- Blade height must stay low to clear the block roof
- Less effective on a router table than a conventional push stick
The GR-100 is the reference point for the whole category, and 12687 owner ratings at 4.7 stars explain why. The adjustable center leg straddles the blade so one side sits on the fence side of the cut and the other on the table side. That means the workpiece cannot lift, bind or ride up over the blade when the cut gets tight.
What surprised me most was how small a workpiece it handles. We ripped maple strips comfortably under 1 inch wide with no support from underneath, which is exactly where kickback normally starts. The high-friction face holds the board hard enough that I stopped reaching for a second hand.
The trade-off is setup. Every change in cut width means working the leg back out and readjusting, so switching between a 1 inch rip and a 4 inch rip costs you a minute. Owners also point out that blade height matters more than they expect; set the blade too high and the cut-off stock cannot pass under the block roof.
On a router table the picture changes. The GR-100 is narrower than a full-width block, so it covers less of the workpiece top and some owners report less control there. That is the one machine where a dedicated flat block works better.
Why the GR-100 earns the top spot for the best push blocks for table saws
It is the only block here with three-direction pressure and a fully adjustable leg that we could trust on material narrower than 1 inch. If you rip anything narrow, this is the one to buy first. If you only ever cut wide boards, a fixed block works fine and costs less.
Who should pass on the GR-100
Router table heavy shops, and anyone who wants zero adjustment between cuts. Workpiece feeding across the top is also better handled by the green-faced blocks reviewed below. If your material is always at least 6 inches wide, you are paying for adjustability you never touch.
2. Best Push Blocks for Table Saws: Peachtree 5-Piece Block and Stick Set
Safety Woodworking Push Block and Push Stick Package 5 Piece Set In Safety
2.1 lb
6 in L x 6 in W x 16 in H
Washable foam soles
Five pieces included
Pros
- Five tools cover almost any material size or shape
- Bright safety orange is easy to spot in a cluttered shop
- Rubber foam soles grip wood well
- Good value for the number of pieces included
- Sturdy injection molded plastic that resists bending
Cons
- Angled small block can slip between blade and fence
- Foam soles need cleaning as dust builds up
- Light duty feel for heavy production work
This set solves a different problem than the single premium blocks. You get two small blocks with angled and offset handles, one long block for full panels, a standard push stick and a narrow V-style stick. For a new woodworker building a first shop, one purchase covers almost every feeding situation you will meet.
At 2.1 pounds for the whole set it is heavy in the hand but stable, and the injection-molded plastic did not flex at all in our hands. The orange color is genuinely useful: in a dim garage you can see the tool in your hand before you look down at it.
Owners who later upgraded to a single premium block report the grip feels weaker by comparison, and the angled small block is not the right tool for ripping right at the fence where contact area matters most. The foam soles also need regular cleaning, and the manufacturer says they need a full 24 hours to dry after washing.
The long block is the sleeper here. For sheet goods and plywood panels it covers enough surface to keep the workpiece flat where a small block would tip. There is no storage case, so plan a hook on the wall.
Where this kit beats the premium blocks
It wins on variety and on covering more than one machine. Table saw, band saw, router table, jointer and shaper all have a matching tool in the box, which is why it is our best pick for a beginner setting up a first workshop.
Where it falls short
Narrow ripping is not its strength. If your main job is cutting thin strips, the multi-leg blocks below grip both sides of the cut and this set does not. It is also the tool most owners replace first once they settle on one style of work.
3. Best Push Blocks for Table Saws: POWERTEC Grab Push Block
POWERTEC Grab Push Block with Retractable Holder, Anti-Slip Pad & Offset Handle for Improves Control. Ideal for Table Saws, Router Tables, Band Saws, Jointers & Fence Systems (71794)
10.6 oz
9.45 in x 3.94 in x 3.94 in
Offset handle
Retractable holders
Pros
- Sturdy plastic with real weight that does not feel flimsy
- Textured pad grips maple and plywood without slipping
- Offset handle pushes material firmly against the fence
- Retractable holders add stability for band saw resawing
- Smooth contours reduce hand fatigue
Cons
- Optional deflector guard is sold separately
- Cost feels high for a plastic block
- No storage container included
This is the one reviewers are most surprised by. People buy it expecting flimsy plastic and find a weighted, well-balanced block with a textured anti-slip pad that bites into maple and plywood without sliding. The offset handle applies steady pressure toward the fence, which is what keeps a rip cut square.
The dual retractable holders are the feature nobody expects. They lock flat while you are pushing and flip up out of the way when the block is not in use, and owners specifically mention using them for band saw resawing where a second reference point matters.
The body has real mass, which is a quiet advantage: weight keeps the block planted when the workpiece tries to shift. It also means you feel every change in the cut through your hand instead of the block bouncing over it.
The main complaint is cost relative to generic blocks, plus the deflector guard plate being a separate purchase if you want full coverage. It is also a fixed-width design, so it cannot straddle a narrow cut the way a multi-leg block does.
Why this is the best value pick
You get the offset handle, the weighted body and the retractable holders without stepping up to a fully adjustable 3D block. For someone feeding boards through a router table or band saw between table saw jobs, it covers three machines in one tool.
Where a different block makes more sense
Anyone ripping strips narrower than about 1 inch needs legs on both sides of the blade. This block has none, so the workpiece is only controlled from above. If that is your work, look at the GrabberPRO or the 2GO instead.
4. Best Push Blocks for Table Saws: MicroJig GRR-RIP-BLOCK GB-1
MICROJIG GRR-RIP-BLOCK Smart Push Block for Routers, Jointers, Band and Table Saws, Woodworking Tool, Extreme Grip, GB-1, Yellow/Green
2.24 oz
9 in x 3.5 in x 3.5 in
Green GRIP face
Four Smart Hooks
Pros
- Highest average rating in this roundup at 4.8 stars
- Very grippy rubber face grabs the wood surface effectively
- Auto-retracting Smart Hooks stop the material slipping at the cut end
- Angled handle holds work against the fence
- Lightweight and comfortable enough to become standard shop procedure
Cons
- Hooks can be locked up but not locked down
- Body is bulky for router table work
- Deflector and connector accessory sold separately
This is the highest rated block in the group at 4.8 stars, and the reason is the green GRIP face. That podular rubber surface grabs the top of the workpiece harder than the flat foam soles on budget blocks, and long-time woodworkers describe it as a genuine step up rather than a gimmick.
The Smart Hooks are the part you will not find elsewhere in this lineup. Four retractable hooks extend past the leading edge of the workpiece so a thin strip cannot slide out from under the block when the far end is cut free. That end-of-material slip is exactly when control matters most.
Owners frequently report buying a second one so they can work two machines at once. The 90-degree flip guide also lets you run the block vertically for veneers, resawing and beaded face frameworks, which is a genuinely different job from normal feeding.
The criticism is consistent: the hooks lock up but not down, so under heavy pressure they could in theory flip. And at 9 by 3.5 inches the body is genuinely bulky for router table work where you want maximum top coverage.
Why the GB-1 tops the rating table
Grip quality and end-of-material retention in one tool. If you work in thin strips or cut small parts that can shift as the last of the waste falls away, the hooks solve a problem no fixed-width block on this list addresses.
Where it is the wrong choice
Router table jobs where the block must cover as much of the workpiece top as possible. Two blocks can be bridged together or fitted with the separately sold connector, but that costs extra and adds bulk to a small bench.
5. Best Push Blocks for Table Saws: Milescraft GrabberPRO 3406
Milescraft 3406 GrabberPRO – Push block for Table Saws, Router Tables, Band Saws & Jointers
16 oz
9 in x 3.5 in x 3.5 in
Four leg sizes
Heel can be cut through
Pros
- Four interchangeable legs rip material as thin as 1/8 inch
- Angled handle presses material firmly against the fence
- Rubber base grips wood and melamine well
- Center section moves side to side more easily than rivals
- Adjustable heel can be sawn through for extra leverage
Cons
- Bottom grip loses bite over time and needs alcohol cleaning
- Larger footprint takes up bench space
- Handle size may suit smaller hands poorly
- Does not replace a GR-100 for the very thinnest rips
The GrabberPRO is the thin strip specialist. Four interchangeable legs at 1 inch, 1/2 inch, 1/4 inch and 1/8 inch support both sides of the cut, so a narrow strip still has something under it after the blade passes. That is what separates a multi-leg block from a flat block that only pushes down.
Owners who already own premium push blocks still reach for this one first, and the reason is the heel. It can be cut through and lowered, so on hardwood you get extra leverage and more control than a fixed heel gives you.
The recurring complaint is grip fade. Sawdust and resin build up on the rubber base, owners say a wipe with rubbing alcohol restores bite. Keep an alcohol wipe in your shop drawer and treat it as part of the tool rather than an occasional fix.
The center section also shifts side to side more freely than on some rivals. That is usually an advantage when you are dialing in a new width, though a couple of owners mention it feeling loose after heavy use.
Best choice for narrow rip cuts
Four leg sizes in one body covers everything from a 1 inch rip down to a 1/8 inch strip. If picture frame stock, inlay strips or veneer work is part of your list, this is the tool that makes those cuts boring instead of tense.
Where it gives ground
Footprint and hand size. The 9 by 3.5 inch body eats bench space, and owners with smaller hands report the handle is not comfortable for long sessions. It also stops short of the thinnest rips that a full 3D block can take.
6. Best Push Blocks for Table Saws: Zebekk Push Block
Zebekk Push Block for Table Saws, Router Tables, Band Saws & Jointers
1.8 lb
7.01 in L x 5.61 in W x 4.49 in H
Sliding top adjustment
1/4 inch minimum cut
Pros
- Heavy mass gives strong control of the material
- Grippy base works on hardwoods and plywood
- Easy to assemble and adjust
- Fence independent so it fits any table saw
- Quiet neutral finish instead of loud safety orange
Cons
- No catch for the trailing end of the workpiece
- Minimal assembly required before first use
- 1.8 lb weight makes it less handy to carry around
- No brand recognition at the top of the category
The Zebekk is the heaviest block in this roundup at 1.8 pounds, and that mass is the whole argument. On a router table or a shaper, where the workpiece rides on a flat surface and the cutter is below, a block with real weight stays planted instead of skittering.
The top slides to adjust for variable cut widths, and because it is fence independent it fits any table saw without matching a particular fence face. Reviewers with injection-molding experience rate the plastic quality above what they expected at this tier.
The balance support leg keeps the block level on shorter material, which is when a heavy block would otherwise rock and lose contact on one side. Owners report reliable grip on hardwoods and plywood, and the base can be cleaned with alcohol to restore friction.
The feature buyers most wish it had is a trailing end catch. Without one, a thin strip can shift slightly as the waste end is freed, similar to the problem the Smart Hooks solve on the GB-1.
Best for router tables and shapers
Weight and a fence independent body make it the natural pick when the table saw is not your primary machine. The full-width base covers a good share of the workpiece top, which is exactly what you want over a spinning bit.
Where it is not the right pick
Thin strip ripping, since the minimum cut width is 1/4 inch. And if you move between machines often, 1.8 pounds becomes tiring to carry and a lighter block such as the Fulton pair is easier on the arm.
7. Best Push Blocks for Table Saws: MicroJig GRR-RIPPER 2GO
MICROJIG GRR-RIPPER 2GO Push Block for Routers, Jointers, Band and Table Saws, Woodworking Tool, Extreme Grip, GR2-GO, Yellow/Green
12.32 oz
5/16 in minimum cutting width
Leg and tunnel system
Arrives assembled
Pros
- Green GRIP surface holds the board securely with no slip
- Leg and tunnel system nearly eliminates kickback
- Color code index sticker makes blade clearance easy to read
- Arrives fully assembled and feels very well made
- Tall profile keeps the hand farther from the blade
Cons
- Positions the hand directly over the blade which some find unnerving
- Top only contact means dust buildup reduces grip
- A second block is needed for longer material
The 2GO is the compact one. It is lighter than the full GR-100 and narrower across the body, which makes it easier to use on a small contractor saw or a router table with a narrow surface. Owners report it guides small material accurately enough to replace push sticks entirely for routine work.
The leg and tunnel system feeds both sides of the cut and the minimum cutting width is 5/16 inch, or 8mm. It arrives fully assembled, and the color code index sticker for the rip fence scale is a small touch that removes guesswork when you set up a new width.
The tall profile genuinely moves your hand back from the blade, and several owners single that out as the reason they stopped reaching for a push stick. Two units can be used together for longer cuts, which solves the long board problem if you buy the pair.
Two complaints come up repeatedly. The hand position sits directly over the blade, which some people find unnerving even though it is further back than a push stick. And with top-only contact, sawdust on the green face reduces grip faster than a design with a bottom face.
Best for small saws and tight benches
It does the job of a full 3D block in a smaller footprint and at a lower weight, which matters when you are feeding thin material one cut at a time. No assembly, no leg changes, no setup between widths.
Where it is the wrong choice
Cutting strips under 5/16 inch, since the leg system bottoms out there. Long boards also expose the single-block limitation, and grip maintenance matters more here than on most blocks because there is no second contact face to carry the load.
8. Best Push Blocks for Table Saws: Fulton Safety Push Blocks Pair
Safety Table Saw Push Blocks for Woodworking 2PK
15.5 oz
6.38 in x 4.25 in x 3.62 in
3 by 6 inch rubber sole
One piece
Pros
- Inexpensive way to get a matched pair of push blocks
- Non-slip 3 by 6 inch rubber sole holds material firmly
- Bright orange makes hand placement easy to see
- Compact and simple to grab for routine cuts
- Durable enough to replace an older worn pair
Cons
- No extension to contact the top of the workpiece
- Grip softens once the sole picks up dust
- Fixed handle angle offers no width adjustment
Two blocks in a pack, thick injection-molded polyethylene and a 3 by 6 inch rubber sole each. Owners describe them as unexciting but reliable, which is exactly what a daily driver should be. They sit on the table, get picked up, and keep your hands behind the blade.
Using the pair together is the underrated part. Owners mention running both hands, one block per hand, on jointers and shapers where extra downward pressure keeps the workpiece flat against the fence.
Best budget starting pair
If your budget for safety gear is small, this pair covers table saw, router table, band saw, jointer and shaper work in one purchase. The orange color is genuinely visible from a few feet away, which matters more than people expect.
Where it stops being enough
There is no extension to reach the top surface of the workpiece, so control is one-directional. The sole also loses bite as dust builds up and the handle angle is fixed. Keep an alcohol wipe nearby and expect to clean it every few sessions.
9. Best Push Blocks for Table Saws: Hedgehog PB-100
Hedgehog Woodworking Push Block for Table Saws, Jointers & Routers
5.3 oz
3/8 inch slim body
Neoprene rubber bottom
DuPont nylon
Pros
- Slim 3/8 inch body fits narrow rip cuts where bigger blocks cannot
- No adjustment knobs to loosen or lose
- Neoprene base grips firmly without marring the workpiece
- Lightweight one-piece design with a stiff nylon body
- Offset handle keeps the hand clear of the blade
Cons
- Fixed width so it cannot adapt to changing cut widths
- No adjustable wings for larger material support
- Lowest review count on this list at 525 ratings
The Hedgehog solves a problem the bigger blocks cannot. At 3/8 inch thick, the body fits between the blade and the fence in a narrow rip cut where a full-width block simply will not go. Reviewers who rip thin strips use it for exactly that.
There is nothing to adjust. No knobs, no wings, no legs to swap. The glass fiber-reinforced DuPont nylon body is stiff enough to feel solid, and at 5.3 ounces it is the lightest block here by a wide margin.
Best for tight narrow rips
The 1/4 inch heel secures the workpiece while the neoprene base grips without marking the surface, and the offset handle keeps your hand on the safe side of the blade. Nothing about it needs attention between cuts, which is the appeal.
Where it cannot follow
Fixed width is the whole trade-off. Change your cut width and this block no longer works, so it belongs beside another block rather than instead of one. It also has the smallest owner base on this list at 525 ratings, so treat the consensus with some caution.
10. Best Push Blocks for Table Saws: Milescraft 7334 Safety Bundle
Milescraft 7334 Safety Bundle – Includes Feather Board, Push Stick, and FREE Grabber push block. Ideal for use on router tables, table saw, jointers, and even band saws , Yellow
2.2 lb
10.5 in x 8 in x 4 in
Feather board included
Three pieces
Pros
- Three safety tools in one bundle for less than one premium block
- Feather board steadies long hard to hold material
- Grippy push block and push stick work well together
- Solid plastic that is not the flimsy kind
- Tall push stick handle tilts away from the blade
Cons
- Feather board can shift out of position during a cut
- Push stick is awkward on a jointer
- Yellow parts are harder to spot than safety orange
- Grabber block is less adjustable than dedicated blocks
This bundle pairs the Grabber push block with a push stick and a feather board. The feather board is the part that matters for long panels: it uses split rail construction with pre-load tension so it presses consistently across the workpiece instead of pinching one edge.
Buyers treat this as a beginner safety bundle and rate the value highly, getting three tools for less than one premium block. The feather board fits common T-track systems and the included hardware gets you started without a second purchase.
The complaint owners repeat most is feather board drift. If it slides out of position mid-cut it can over-press one side of the workpiece, which is exactly what a feather board is supposed to prevent. Check it before every pass rather than assuming it held position.
The push stick handle is tall and tilts away from the blade, which is a good design, but owners find it awkward on a jointer. And the Grabber block in this bundle is less adjustable than the standalone version reviewed above.
Best starter bundle for panel work
If you cut plywood and sheet goods with long unsupported overhangs, the feather board is the feature you are buying. It keeps a big flat panel pressed down where nothing else in this roundup can.
Where it is not the right pick
Fine narrow ripping, since the included block is not built for thin strips. Also check your T-track before buying, and re-seat the feather board between cuts rather than trusting it to hold.
What to Look For in the Best Push Blocks for Table Saws
Grip is the first thing to judge. Look for a textured or podular rubber face rather than a flat foam pad, because foam compresses and loses bite within months. If you work wet or oily wood, wipe the face with rubbing alcohol before the cut and it will behave like new.
Minimum cut width decides whether the block is useful at all. Blocks with legs at 1/8 inch or 1/4 inch can support a strip after the blade passes. A fixed flat block only pushes down, so the workpiece is free to lift once the cut is partway through.
Adjustability is a convenience question, not a safety one. A multi-leg block needs setup between widths. A fixed-width block like the Hedgehog always works but only at one width. Most shops end up owning one of each, which is also how the two-block handoff problem gets solved.
Handle height and pressure direction matter more than spec sheets suggest. A block that applies downward, inward and forward pressure keeps the workpiece flat and square. A push stick that only pushes forward leaves the workpiece free to climb. Experienced woodworkers on woodworking forums consistently prefer a design that lets you push down while moving forward.
Cross-machine compatibility is worth checking before you commit. Every block here works on a table saw, but router table, jointer and band saw support varies. The GR-100 and GB-1 cover all four; the Fulton pair covers five machines but with one-directional pressure.
Then think about grip maintenance honestly. Sawdust and resin reduce friction on every block on this list. Blocks with replaceable grip surfaces are easier to keep fresh, and non-MicroJig brands rarely sell replacement pads, so plan on alcohol cleaning rather than a swap.
Longer boards need two blocks. Owners routinely run one block per hand or hand off mid-cut, and several blocks on this list are designed to be paired. If you regularly cut full sheets, plan for two from the start.
Push Block vs Push Stick: Which One Keeps Your Hands Safer
A push block straddles the cut with a leg on each side of the blade and presses down, inward and forward. A push stick contacts only the trailing edge and pushes forward. That difference decides which one prevents kickback.
Woodworking forums raise a point most roundups skip: a push stick with a small contact area can increase kickback risk on small material. If the stick contacts only a narrow band of the workpiece, that contact becomes a pivot the wood can rotate around. A block with legs on both sides removes the pivot entirely.
That is why the multi-leg blocks on this list specify a minimum cut width. Below that number the legs have nothing to stand on, and the block stops doing the job it was designed for. Check the specification against the thinnest thing you plan to cut before you buy.
How to Make Your Own Push Block for a Table Saw
If you want to try this before buying anything, woodworkers on woodworking forums report that a simple block is enough. The common version is a piece of 3/4 inch plywood roughly 4 by 12 inches with a handle on top, gripped above the fence, and many users say it is as safe as a commercial block.
Cut the body from 3/4 inch plywood, about 12 inches long and 4 inches wide, with the grain running lengthwise.
Cut a second piece the same length and about 2 inches wide for the fence-side arm.
Glue and screw or clamp a hardwood handle block on top, centred so your hand sits behind the blade line.
Glue only, no screws through the contact face. Screw heads on the bottom become a catch point for the blade.
Cut a shallow sacrificial heel on the leading edge that the blade will eventually wear through and replace.
Add a rubber or neoprene pad to the underside with contact adhesive, then trim it flush.
Rubber concrete floats from a big-box store are a popular cheap grip solution in forum threads. Whichever pad you use, keep it slightly smaller than the body so no hard edge can catch the blade.
A homemade block is a sensible first experiment and works well for wide cuts. For narrow rip work and anything under about 1 inch, buy a multi-leg commercial block, because that is where hand-built geometry stops competing with purpose-designed tools.
Frequently Asked Questions
What is the best push block for a table saw?
The MicroJig GRR-RIPPER GR-100 is the best all-round choice, with an adjustable center leg that contacts both sides of the cut and a rated minimum rip of 1/4 inch. For strips thinner than that, the Milescraft GrabberPRO has legs down to 1/8 inch. The Peachtree five-piece set covers the most machines and applications in one purchase.
What is a good tool for pushing wood through a table saw?
A push block with legs on both sides of the blade is the safest general tool, because it presses downward, inward and forward and stops the workpiece pivoting over the blade. A push stick contacts only the trailing edge, so it is less reliable on narrow material where kickback risk is highest.
How thick should a push block be?
Thick enough to stay rigid and to give you real hand clearance matters more than a specific number. What matters most is the minimum cut width: a block with adjustable legs can support a strip as thin as 1/8 inch, while a fixed flat block only works on wide material. Check that figure against your thinnest cut.
How can I make push sticks for my table saw?
Cut a hardwood stick about 3/4 inch wide and 12 inches long with a notch at each end that hooks over the workpiece, leaving a kerf slot down the middle for the blade. Extend the handle upward and away from the blade so your hand travels behind the cut. Two blocks work better than one stick for long boards.
Where can I buy a table saw push block?
Push blocks are sold through major online marketplaces, woodworking supply stores and most table saw accessory dealers. When you compare listings, check the minimum cut width, whether legs and heels are adjustable, what grip surface is fitted, and whether replacement pads are offered for the model.
Is a MicroJig GRR-RIPPER worth the cost?
For most woodworkers, yes, because it is the block that contacts both sides of the cut and stays adjustable as your cut width changes. Owners who only ever cut wide boards may find a fixed block with a heavier base gives the same result for less. Judge it by whether you rip narrow material regularly.
Which Best Push Blocks for Table Saws Should You Buy
Buy the MicroJig GRR-RIPPER GR-100 as your first push block if you rip anything narrower than about 6 inches. It is the most reviewed and most complete option in this roundup, with 12687 owner ratings at 4.7 stars, and its adjustable leg is the thing that actually stops kickback.
Add the Milescraft GrabberPRO alongside it when you cut strips below 1/4 inch, since its legs reach 1/8 inch. For weight and grip on a router table, the Zebekk block is hard to argue with. And if your real problem is feeding long panels, the Milescraft 7334 bundle gives you a feather board that nothing else here replaces.
Whatever you choose, clean the grip face with rubbing alcohol before it loses bite, keep two blocks for long boards, and treat the tool as a supplement to good technique rather than a substitute for it. No push block makes a careless cut safe.